Saturday, September 19, 2009

Midnight Grey Death (sealing the tanks)

Normally when people refer to the fuel tank sealant there are a number of words to describe it -- Proseal (a brand name), Black Death (it is sort of black) or other names that have four letter words in the title.  When we were working Darren interjected a little levity and said that it really wasn't black it was more like a Midnight Grey.  Henceforth we'll refer to it as "Midnight Grey Death".  This has to be the worst thing we've had to work on so far.  The prep work is very demanding as the instructions require you to score the mating surfaces really well and then clean it so that there are no contaminants.  However, you can't touch the aluminum without gloves because your skin oils will weaken the sealant.  So, we got to spend the day wearing blue gloves.  But, it gets worse, the tank sealant -- midnight grey death -- is sticky and it gets everywhere.  Oh yeah, it really likes to stick to the blue gloves.  Supposedly sealing is like icing a cake but imagine if cake icing would stick to everything and couldn't really be cleaned off except with some awful chemical and major scrubbing.
Anyways, I've complained enough.  For all of that we actually made good progress on both fuel tanks.  We installed and riveted the fuel tank stiffners in both tanks.  On the left tank we also installed the fuel tank filler flange, the tank drain flange and sealed the rivet heads.  We're well positioned to get the tanks together this week.  This is one of those jobs that was rotten to do but the memory will fade...eventually.
Oh yeah, we also did some work on Thursday night last week.  We riveted the inboard and outboard flap brackets, installed the centre bracket, and matchdrilled all of the reinforcing angles.  Also we assembled the aileron attach brackets.






Saturday, September 12, 2009

Bucking Rivets

Yes, that was always meant to be a "B".  Sorry for the lack of updates over the last few weeks but the work hasn't been exciting enough to write about in detail.  However, the work may not have been unique or exciting but the results are great!  We're finished riveting the leading edge on the main spar (done last weekend) and riveted on all of the top skins and "J" channels.  I'm not interested in counting the number of rivets we've installed over the last couple of weeks but suffice it to say that it was alot.  Once we finished riveting the wing skins,  we got to work on the aileron and flap attach brackets (we'll post pictures of this but if you can't wait you can take a look at the left wing pictures). The aileron brackets are fairly straight-forward (that is until you need to figure out what needs a countersink and what doesn't) but the flap brackets have some reinforcing angles that need to be cut.  All of these parts are cut and ready to be match drilled, prepped and primed during the next work session.











Sunday, August 30, 2009

Leading Edge Assembly

Today we started by cleaning up the workshop.  We wiped down the wing skeleton and vacuumed the workshop.  After all of the match driling and deburring there was a lot to be cleaned up.  Next we riveted the leading edge together.  There are a lot of rivets and we had to work to get the skin to line up tightly.  We finished up the riveting and installed it on the main spar.  Finally we painted the overlap on the skin. 




Wednesday, August 26, 2009

Right Wing prep work is finished

Tonight we finished up the last of the preparations.  We reassembled the leading edge and installed the platenuts for the leading edge.  Finally we prepped and primed the spar countersinks and the remaining parts.  Next time we'll work on assembling the leading edge.

It was time install some pieces for the landing lights in the leading edge.... This pattern is ment to ensure the proper placement of platenuts.


The main spare after the machine counter sinced holes have been primed. 

Saturday, August 22, 2009

This much fun should be illiegal


Well, today was another day of prep work.  We put in a lot of hours and now we're almost finished all of the prep work on the right wing. To speed things up we split up to cover more territory but I won't try to allocate the tasks to a specific person.  We worked on deburring and dimpling all of the remaining rivet holes on the wing skeleton and skins, In addition we installed the plate nuts on the right fuel tank "Z" brackets (the fuel tanks have been set aside until the new caps arrive.)  We also machine countersunk the main spar rivet holes.  Plus, we disassembled, deburred and dimpled the leading edge ribs and skin.  Next we drilled the plate nuts to "W-919" which is the place where the fuel tank gets attached to the leading edge.  Finally we prepped and primed the leading edge ribs and skins.  Of course, all of the skins still had the blue plastic protective coat on so that was cut off before any deburring or dimpling was done.  All in all, it was a great day of work but it looks like we've taken a giant step backwards now that we have a bare wing skeleton sitting in the stand.  Next time we'll start riveting the right wing leading edge together so the wing starts to look like a wing again. 

Scott working on one of the leading edge ribs.


Darren machine countersyncing some holes on the main spar.


Darren drilling out some holes for the platenute attachments on the the wing tank re enforcement plate.


Scott priming some of the pieces... it gets a little cloudy in there. 

Thursday, August 20, 2009

More fun than a barrel of monkeys

Not!  We spent all of today doing prep work.  First we match drilled the fuel drain flange to the left fuel tank skin and that was the end of the fun tasks.  Next we disassembled the left fuel tank and proceeded to deburr and dimple all of the parts.  Once that was done we set the left fuel tank aside.  We are waiting for the delivery of the nice, shiny, stainless steel fuel caps.
We then moved onto the right wing skeleton.  We removed the top skin and starting working on deburring and dimpling all of the parts.  Luckily with two of us we can employ a divide and conquer strategy.  Darren worked on removing the blue plastic protective coating from the main skin.  He then deburred both sides of the sheet and beveled the skin overlap.  While he was doing that, I worked on deburring and dimpling all of the holes in the wing skeleton.  Afterwards, we teamed back up to dimple the main sheet.  Lastly we prepped and primed a few of the fuel tank parts and the main wing skin.

Scott either taking some clecos out, or putting some clecos in (the process is repeated alot...).

 
Darren doing some pre-paint prep work. 

Sunday, August 16, 2009

Fuel tank progress

Today we did work on both fuel tanks and finished up the preparation work on the right tank.  The first task was to use the flycutter on the drill-press to cut out a hole in the inboard tank rib for the access cover (both left and right tanks).  Next we match drilled the access covers to the end-ribs and then match drilled the stiffner rings to the ribs.  Because the access panel is secured using screws, we had to install platenuts (which means 2 rivet holes in addition to the screw hole).  Before the platenuts could be installed, the rib needed to be deburred and dimpled and the stiffner ring was countersunk.  We next drilled the holes for the fuel pickup tube, fuel vent line and the capacitive sensor connector.  Once that was done, we then installed the stiffner and platenuts to the rib (this was done on the left and right fuel tanks.)  Next we match drilled the fuel tank drain flange to the right tank skin.  Finally we concentrated on the right fuel tank.  We disassembled, deburred and dimpled all of the ribs and skins.  We are waiting for the new fuel caps to arrive before we start to seal the right tank.  Next session we will wrap up the prep work on the left tank in the hopes that the tank caps arrive before we're ready to start sealing the tanks.  


Since we are using a capacitive fuel sensor we had use a different acess cover for the tank.  We used the access cover included with the base kit to place the hole used for the fuel pickup tube.


The end rib, re-enforcement plate, and access cover prior to some prep and assembly work. 


Darren cleaning up a re-enforcement plate. 


 An end rib with the plate-nuts, and re-enforcement plate riveted into place.


 The access cover sitting in place.


A close-up of the skin after some dimpling work. 


 The skin more or less ready for assembly.


Another  close-up of the skin after some dimpling work.